Видео

Nice video

Just about every lvp manufacturer tells you specifically not to use a hard plastic laminate tapping block. This poor guy barely knows what he is doing. He's not even racking out his flooring before he installed. Not only are tapping blocks like that a waste of money they destroy flooring. Snapping click vinyl plank is supposed to be installed without even needing a hammer In most cases. I've been doing flooring for 29 years and was Union trained

High quality video. Nice work!

Sheet vinager repair

It's just a basement someone did it from church probably,

Could you do an in-depth video on the best way to install shoe?

Thank you, God bless you and your family. Palermo's from Chicago.

Beautiful. This gives me the courage to fix a plank that has been driving me crazy.

That looks great! Awesome tip about the latex, too, thanks!

Buddy, you just blew my mind!! Thank-you, I just hope the wear layer will be as easy to peel as yours. Cheers.

Outstanding.... Just what I needed. Thanks!!

I was just quoted 7k to fix my bathroom floor. I need help

Alright, I used your video and replaced 4 vinyl planks that had a deep scratch from when my son moved a steel based chair. It looks amazing. Now I do have a question just today I had to tighten up gaps in the kitchen approx. 4 foot square area looked like a jig saw puzzle crooked from movement. The floor is 8 years old not happy with vinyl. However, by the time I was able to get the area back to new looking the last row I had to replace 2 planks since no matter what I did they would not move. At the end of it all I have a gap along the length of the planks approx 1/8 inch. What can I use to fill this gap the planks are a dark oak/brown Torlay color - Avalon and of course no longer able to purchase. Lucky I had 3 boxes left over. Can you recommend a gap filler - watched a lot on RUclips but not great results by most. Regards and Thank you fro the vid again.

How would you do the same for a situation where the already laid floor is perpendicular to the opening and you want to run the next room in the other direction? Namely a "T" joint. I guess the real question is how would you cut the plank ends to be even with the new full length piece? and then do the glue trick.

There is no way a pro would even put that down over carpet glue😳 that’s genuine church cheapness. Pinching pennies when God has all the silver and all the Gold!

You are awesome. Thanks for the video.

Not knowing the situation....just a question.... was this a professional? Did the church go with the lowest bid? Was this discussed before the installation? I wouldn't be so quick to cast blame before the facts come out. Let's hear what the story was.

What is glue work for click together vinyl plank on stairs if not what glue would be best use plenty of blue before different brands but it just doesn't stick like I wanted to film in the back of the planks

its the dont care just get it done... hahaha

What a shame! Would have been a nice job if they had taken the time to properly prepare the concrete floor.

Tell me it was someone from the church and not a 'professional'

How do you fix wrinkles/bubbles in a perimeter felt back sheet vinyl congolum product it wasn't rolled with the wear layer out or tubed I heard about heat socking it with a hair dryer and then apply a tray of ice to the wrinkle to thermal shock it have you got any other ideas if that doesn't work

great video right to the point 🤓

Awesome

How does it do when you swoop the iron out at the end?

Bad camera work with the tuck and tap down

That tile job…..Yikes..😬😬😬

Greetings. Good grief. That's a shame. I just had electrical work done in my home and a day later I discovered two impact gashes in my laminate flooring - my assumption is, the technicians dropped something very heavy. I don't love laminate flooring, but that is all I have till I can replace it, but in the mean time, do you have any suggestions how to repair laminate gashes instead of replacing the whole planks? I'd sure love to see a video post of that if you do.

Did you have to get a special blade for your tabke saw or just use a standard 24 tooth?

So how much would you charge per step if I were to take this method

I love your passion for craftsmanship. Quick question though. If I lay base before carpet install, what space should be under the baseboard and what distance from said pre-installed base should I place my tack strip?

I am in the middle of a room remodel in my house and was debating whether I sbould lay new carpet and then install baseboard over top. If I take old carpet out and install baseboard, how much room should I leave under the baseboard to then lay carpet after base install? Going to be using a more plush carpet as it is a bedroom. Thanks.

That carpet I’ve had to double tackstrip everything. Or it likes to wrinkle on all the edges later on

great use for that situation nice

Awsome work

Best video I have seen on replacing bad planks and instructions were done perfect - thank you

Way to hard , roll back double cut, and seam seal , roll! How can you make any money at that way to long

Ultimate blade on a scrapper. Lasts for years and does the whole steps in seconds.

Can you put this down over slight damp concrete?

Nice work!

Yeah, it’s pretty crazy how many installers will seam the doorways before even a single stretch. The problem with that is if you properly stretch the carpet afterwards, you will definitely get bubbles in the carpet everywhere. That’s why those who do so don’t get a good stretch on the carpet and wrinkles appear within a few months.

If you fold carpet back and measure at each end of hall as long as there the same measurements should be good that’s what I do but good job anyway

I also use the ol tapperoo technique glad to see it being shown to the public and not being hid away in the vaults of flooring guild..great instructional program would recommend to my friends

I get what your doing, I do the same with prints. But wouldn't of been quicker with the same results by just staying off the doorways row cutting each one separate. Then buring the doorway? looks like the bedrooms are straight drops with plenty of wiggle room to move the carpet around to line up the seams.

👍🏻

I just found me a new carpet dad

I wish you could name every tool you just used

Very smart to run the row down the middle so your doors are straight and you can run a row on those. Hopefully you’re getting paid well because we both know this takes twice as much time as straight edging and tracing with top cutter

Watching someone as picky and perfectionist as me is very therapeutic! Some guys just don't get the small details make the biggest difference.

Doing that thing like a pattern lol, pretty serious work for a cut pile, nice